9/15/13

XS650 Special project

Not quite done, but I got it up and running and played around on the property with it. I love it. It feels like a badass big-block enduro.
100_4191

100_4202

100_4201

100_4205

Here is a quick walk-around video.


The little mufflers sound good, maybe a bit louder than what I'd prefer.

XS650 Special project

It is almost road ready. I still need to bleed the front brake, route the fuel lines, make a block-off for the tach drive, and a few other small things to finish up. Once it is riding again I'll repaint the tank badges and de-badge and paint the side covers.
100_4166

100_4163

100_4174

100_4154

9/14/13

XS650 Special project

I'm getting some of the final things done on the '79. The old '75 head pipes I'm using had some heavy rust in spots.
101_0177

They cleaned up great with sandblasting. There is pitting from the rust in the bad areas, but it'll be fine. I also blasted the new mufflers to rough the chrome up for paint.
101_0180

I'm using VHT flat black.
100_4148

They came out very nice. I don't have a way to oven cure the paint, so just let them sit in the sun, and then they'll finish up once the bike is running. One tip on painting under the flange area, slide the collar down and paint that part of the pipe. The paint tack dries quickly (about 10 minutes), then slide the collar back up being careful to not touch the pipe. Use masking tape to hold it in place and paint the rest of the exhaust. When removing the tape to install the exhaust, make sure the collar doesn't slide down or it can leave marks in the paint.
100_4144

To go with the new coil, Autolite 63 plugs and NGK non-resistor caps.
100_4142

The bike had a braided front brake line when I got it, but it was too long and a two piece. Also, the new headlight mounts to where the junction block was originally. The new line is a Russell R58132S 34" line with a R4047C straight banjo for the master cylinder and a R4050C 35 degree banjo for the caliper. The new petcock is Custom Chrome part #12727.
100_4137

I wanted to leak test the tank where I'd welded in the new bung, and here is a simple way to do it if the tank has a raised area around the fuel filler. Cut a section of an old inner tube with the valve stem, and get a radiator hose clamp.
100_4149

Install the petcock or a pipe plug (hand tight is fine for leak testing), and clamp the inner tube around the fuel filler. Tighten the clamp just enough to seal. You want it to be able to pop off if you use too much pressure. Preferably use a bicycle tire pump and put a few PSI in it. Then use a dish soap and water mix and apply around the area to be tested with a q-tip. If you have any leaks it will bubble up like crazy.
100_4152

9/7/13

DT1


source: http://auctions.search.yahoo.co.jp/search?p=dt&auccat=26316

XS650 Special project

I've been doing some more assembly on the '79. It should be riding by next weekend.
100_4130

100_4121

100_4124

100_4115

9/2/13

XS650 Special project

This project is just a tank, seat and wheel swap, but I think the electrical work ended up being the single most time consuming part of it. Anyway, the wiring is done.
100_4111

100_4104

The wires from the Ford tractor ignition switch were touching the gusset on the other side, so to prevent any problems I went back and made a spacer from some 1" OD aluminum tubing, and re-soldered the wires at an angle, so plenty of clearance inside now.
100_4096

today

100_4085

100_4088

100_4089

100_4094