8/6/12

fast and easy old motorcycle tire dismounting at home

I needed to dismount the tires on my XS650 project. The rims and hubs will be polished, and I'll re-lace with stainless spokes, but first to get the tires off. I don't want to cause any damage to the aluminum shouldered rims, so choose to cut the tires off. I do most all of my own tire mounting and dismounting, and for stiff old tires this is much faster than wrestling around with tire irons. You don't even break a sweat doing it this way.
100_5868

First let the air out, and if it has a tube, remove the valve stem nut.
100_5871

A reciprocating saw with a general purpose blade works best here. It cuts quickly through the bias ply tire.
100_5874

The idea is to cut it as close to the rim as you can, but making sure not to hit it. Then cut the tube and rubber rim strip with a utility knife and push them inside the tire, out of the way.
100_5878

On motorcycle tires I like to use a large C clamp to break the bead loose. I did it near the cut, but it doesn't matter where it is done.
100_5882

Then lay it down and walk the rest of the bead off, just by stepping on it. Then flip the clamp so you can do the bead on the other side.
100_5883

Now to cut the steel bead cord. I like to use an angle grinder with a regular grinding disc for this, but a cut-off wheel would work also. First get the bead of the side that you are cutting as much as possible in the center part of the rim to give you more slack, and use a tire iron to lift up the part that will be cut. Use a rim protector under the tire iron. I'm using one cut from the top of a plastic coffee can here. This is the only time a tire iron is used with this method and since you aren't trying to get the bead over the rim lip, almost no force is used.
100_5892

Then cut away, keeping the tire iron between the grinder and rim. When you see sparks you are into the steel bead cord, shown here. Once you cut through the cord you'll see and feel it release. Then just a small amount of rubber to cut. For that a utility knife will work.
100_5896

Then just pull the bead off by hand, starting at the cut. Next, pull the tube and rim strip out.
100_5900

Usually the other side will just pull off by hand, like this one did. If not, cut the bead.
100_5901

The wheel is ready to disassemble and polish, without even the slightest scratch.
100_5906

8/4/12

staying busy

Now to paint the frame. I got two cans of primer and two of color.
100_5844

First the self-etching primer goes on.
100_5815

I had a quart can of gloss black Rust-Oleum, so brushed it in a few places. Some tight areas are difficult to get into spraying without getting too much coverage in nearby spots, which can cause runs. With the brush you can work the paint into seams and under brackets to make sure there is good coverage. It just makes the spraying easier and faster.
100_5835

I then sprayed the brackets and tabs, and hard to reach areas like the inside of the neck gussets. Some of these, like the side cover tabs, need sprayed from many different angles. The frame tubing itself is the easiest and fastest to paint, and the most visible, so that gets done last. Multiple light coats get the best results.
100_5840

Done! The Rust-Oleum is slow to cure, but since it will be quite a while before the bike gets reassembled it isn't a concern. I will rub it out with a wax after it sits for 30 days or so. This was the biggest chassis part that needed painted, so nice to have it completed.
100_5853

100_5850

100_5854
I had looked into having the frame powder coated, but chose not to. Prices in this area ranged from $150-$200 for just a frame. Blasting and painting myself cost about $40 total for materials, and I have enough paint left over to do many of the other small parts also. Some coaters wanted $80 to do just a swingarm, so quite a savings doing it this way. If the bike was going to be daily transportation I do think the durability of powder coating would be worth the cost. I also knew exactly what I was getting by doing it myself.

8/3/12

staying busy

This week I finish welded a few tabs, and then put the tank and seat on for a last chance look over.
100_5767

This evening I sandblasted the frame, and will paint it in the morning.
100_5781

100_5784

100_5788

100_5792

100_5804

100_5812

7/29/12

XS650 cafe' project

Getting started on the XS650 rebuild, I'm making an extra effort to stay organized. On small projects, like my SR500, it doesn't make much difference. On a long term project, where every nut and bolt gets touched, it can be a big time and money saver. A note book, freezer bags, labels, and a separate camera card (just for this project).
100_5624

I also made a shelf unit from some scrap wood, just for parts that will be going on this bike. This avoids them from getting cluttered with the parts that aren't being used, or other parts.
100_5626

The freezer bags are great for keeping the small bits organized and separated.
100_5646

Lots of detailed pictures can be a big time saver during reassembly, taking the guess work out of things like harness routing. I bought the separate camera card just for this so I won't have to sort through other stuff just to find what I'm looking for. This bike is really more of a resto-mod, being that most of the machine is staying stock, so much of the bike will go back as it was.
100_5659

100_5678

It will likely be 7 months before reassembly starts, so notes of certain things can be a big help later on. Writing down now what parts that will need ordered can save from forgetting something and having to pay shipping costs twice.
100_5715

Just need to remove the engine, and then the real work starts.
100_5713