2/28/16

RT3 MX project

Once I was happy with the fit of the rear frame I welded it on. I then stuck some wheels and forks on to make it a rolling mock-up. I'm super happy with how it's looking. This bike will be finished in yellow and black Yamaha racing colors, with lots of polished aluminum, but that's quite a ways off. Next I'll need to fit an exhaust, convert to a cable operated rear brake, tank mounts, seat, and a few other things.
100_8256

100_8273

100_8265

100_8268

2/24/16

RM100

RM100

Ossa

Ossa Super Pioneer

The Honda Fours

Honda fours 1

Honda fours 2

RT3 MX project

I'm waiting on the weather to do the paint on the XS650 enduro project, so took some time to work on the RT3. I bought the '71 DT1 and '73 RT3 a few weeks ago, and since the '70 RT1 and '71 DT1 won't have any fabrication I thought I'd go a little wild with the RT3.
100_8052

I stripped it down to the bare frame.
100_8068

I'm wanting to do laydown shocks for more rear travel, so will be using an XT500 rear frame section.
100_8078

The rear frame needed narrowed to fit the RT frame, and for the shock mount spacing of the swingarm I'll be using.
100_8085

I cut off the rear frame from the RT3.
100_8086

I'll be using a '77 RM250B swingarm, which is what I also used on the blue tanked '69 DT1. The early DT square swingarm frames use a 12mm bolt, but the RT3 frame uses a 16mm pivot bolt, and the RM swingarm uses 14mm. The RM swingarm does take a 28mm OD bearing or bushing, which is the same size as most Yamahas, so I'll be using XS650 bronze bushings. The machined area on the RM pivot isn't quite deep enough to fit the XS bushings, so I had to shave the last 5mm of the outside of the bushings to fit.
100_8095

Here the bronze bushings are in. The RM pivot is narrower than the RT, so I trimmed down the center spacer of the three piece RT pivot tube leaving the the outside collars slightly proud of the bushings. I'll be using XS650 end caps, since they have a grease seal unlike the RT caps, and will use washers on the outside to make up the rest of the width difference.
100_8100

Here is the RM swingarm fitted to the RT frame. I put a bare set of engine cases in the frame for reference.
100_8102

I then made a simple jig in order to locate the shock mounts in the correct location.
100_8107

Here the rear frame is beginning to be fitted. The jig makes this much easier.
100_8110

Here is the rear frame nearly fitted and close to being ready to finish weld. I put a set of shocks on to see how it is looking so far, and I'm really liking it. I'll also be using an aluminum YZ125C tank that I'd bought at the swap meet last year. I think it will be perfect for this bike.
100_8113

2/23/16

2016 Indiana Motorcycle Expo part 2

My favorite bike at the expo was this '56 KR.
100_8134

100_8137

100_8139

100_8135

100_8177

100_8181

100_8145

100_8235

100_8132

100_8179

100_8175

100_8224

100_8192

I love the KTM RC390. It looks incredible, has got to be super fun, and at $5499 is a bargain.
100_8229

100_8234

Speed City Cycle had the Royal Enfield line on display again this year.
100_8241

100_8238

100_8239

2/22/16

2016 Indiana Motorcycle Expo part 1

Time again for the Indiana Motorcycle Expo. The Indy Rockers Reunion booth had some bikes from the 2015 Rockers Reunion, and was promoting the 2016 event which will take place on June 18th. It is a couple weekends later than previously, but at same Fountain Square location as last year.
100_8120

100_8121

100_8125

100_8122

100_8130

100_8124

100_8126

Here are some of the bikes from the Biker's Showcase, which highlighted competition bikes this year.
100_8222

100_8153

100_8216

100_8211

100_8219

100_8218

100_8157

100_8159

100_8146

100_8147

100_8215

100_8151

100_8196

100_8210

100_8201

The barn find class was a fun contrast to the usual show and shine.
100_8203

100_8205

I really liked this one, a Brockhouse Indian Brave with a 350cc Jawa engine.
100_8209

100_8206

100_8164

100_8167

100_8197

100_8213