3/31/13

today

100_9488

100_9492

100_9478

100_9472

100_9471

I'm an AGV guy. My favorite one is my old (12/2000 date of manufacture) Rossi sun and moon helmet. I got it for $60 new in the box back in 2005 or so since it was "expired".
100_9484

100_9486

3/30/13

XS650 project

This project got started with a swap meet gas tank and exhaust system last year. The exhaust was in good shape with just a few minor scrapes and dings, but had some serious discoloration on one of the pipes. Discoloration is normal on single wall pipes, and I think it looks neat, but this needed cleaned up a bit.
100_9421

100_9424

I used Noxon 7 metal polish to give them a more even look.
100_9428

100_9427

I think they look fine on the bike.
100_9439

I've also been doing some other assembly, the rearsets for one. I still need to make the shift rod for the left side rearset. Rebuilding the carbs will be next.
100_9438

100_9443

100_9446


100_9455

3/25/13

spring

Still snowing. This is just like it use to be in Indiana, a nice snow at the end of March. At least it doesn't stay long this time of the year.
100_9360

100_9378

100_9370

3/24/13

March 24th

From this day in 2012...
100_7842

100_7846

100_7849

...and today in 2013. Supposed to snow through the night. Looks like the plow will be going back on the truck tomorrow.
100_9358

100_9356

3/23/13

XS650 project

There are a few ways to increase the reliability and performance of the XS650 charging system. There are complete permanent magnet alternator(PMA) kits, or plug and play solid state regulator/rectifiers. On my '75 I'm doing the Pamcopete Chrysler regulator and Radio Shack rectifier swap. I like this in that it uses proven, yet very low cost parts that are readily available.

The old mechanical regulator and the new Chrysler regulator, part #VR733 from Autozone. I also bought a connector for it, but you can just use bullet terminals.
100_9288

The old rectifier, and two 276-1185 full-wave bridge rectifiers from Radio Shack.
100_9290

The Chrysler regulator needs the alternator to be modified to work like '80-'84 models by isolating the inner brush. This is done by replacing three steel screws with nylon. The nylon screw were the only thing I didn't buy locally. I bought a 10 pack for under $4 shipped from ebay seller AMS Bugbolts in the UK.
100_9210

The M4 12mm nylon screws in place.
100_9211

This is the alternator connection on the main harness. The black wire was ground, but needs to go to a switched 12V power source (brown wires) with an inline fuse.
100_9327

The new regulator connector soldered in place. Green to green, and blue to brown. The Chrysler regulator grounds through the case, so the black wire gets a ring terminal.
100_9307

There are many ways to mount the regulator. I used one existing mount (bottom front), and drilled two holes in the battery box for the rest.
100_9328

I had some scrap 1/8" x 2" aluminum flat stock and cut a 3.5" piece to make the heat sink/mount for the rectifiers. Heat sink compound is used for this.
100_9311

The original connector cleaned up nicely and was in good shape, so I reused it.
100_9320

Done and mounted. The rectifier mounts in the stock location under the battery box.
100_9342

This is with the side cover on to check clearance. The wires are close, so I'll probably use some stick-on foam to make sure they don't ever rub.
100_9348

A few more electrical parts, the bigger one on the left is the 'safety relay', which I'm going to keep. It cuts power to the starter once the engine is running. I don't know why they thought it was needed, but I guess it doesn't hurt anything. The gray box in the middle is the 'light checker' and the small cylinder on the right is a diode for the brake lining switch. Both of those won't be used. I went through the harness and removed the wires for them also.
100_9338

3/17/13

Mid-America Speedway

The Mid-West Motorcycle Club 30th Annual Swap Meet is being held on April 20-21 at the Marion County Fairgrounds. On April 20 swap meet admission gets you free admission to the motorcycle flat track racing at Mid-America Speedway. The Bultaco Astro Challenge being held the night before the Indy Mile looks to have a packed field, and well known names.

the swap meet

I had a great time at the Boone County vintage motorcycle swap meet. The $6 admission gets you a free hat, and I bought a t-shirt from the Mid-America Speedway guys. They've got a big 2013 planned, more on that later.
100_9277

I didn't buy near as much as the last two times, but found one thing I was looking for, an aluminum 19" rim for the front of my SR500. Hopefully the spoke angles will work with the TX650 hub from the last swap meet. I got a couple old helmets, mainly just for display. The white one is a D.U.N.S. and the blue one a Grant. The white one actually fits me fairly well.
100_9283

I picked up an old Husky tank that is super clean inside, and an unknown seat. Maybe they'll be perfect for a project sometime.
100_9285

3/15/13

Thunder Stroke 111

It is great to see Polaris getting serious, and getting away from the Harley clone engines of the recent Indians.

3/10/13

XS650 project

The '73 TX650 forks I'd bought at the last swap meet, and used parts for the twin disc swap, were missing the bottom caliper bolt, and the one that came off the '75 didn't look so good. It has a chrome acorn head and the threads are 10mm x 1.25. Everything at the hardware stores was 1.50 pitch. I'd bought a set of chrome acorn nuts from MikesXS, and found an exhaust manifold hardware kit at Autozone with studs the right length and in the correct 10mm x 1.25 pitch.
100_9220

This will work. I first cut slots in the end of the studs at the nut end to be able to use a flat blade screwdriver if needed to remove the studs.
100_9225

The calipers mounted. I trimmed the end of the key tab on the outside pad on the left caliper, since it looked like it might not clear the fork slider.
100_9257

Here is where I'm at now on the bike. Next on the list is wiring. I'll be doing the Pamcopete Chrysler regulator and Radio Shack rectifier conversion.
100_9230

100_9250

100_9236

100_9233

100_9240

100_9238

100_9244